SparkFun

SparkFun sell the bits and pieces to make your electronics projects possible. No matter what your vision is, their products and resources are designed to make the world of electronics more accessible to the average person.

SparkFun Qwiic MP3 Trigger

Sometimes you just need an MP3 to play. Whether it’s a theme song as you enter the room or a power song when you are working out. The SparkFun Qwiic MP3 Trigger takes care of all the necessary requirements, all you need to do is send a simple I2C command and listen to whatever is on your micro SD card. Read more...

  • DEV-15165
£21
Only 2 left!

SparkFun USB-C Breakout

With this USB breakout you will finally be able to incorporate a USB-C connector into your projects without needing to solder each tiny SMD pad. The SparkFun USB-C Breakout supplies up to three times the power as previous USB iterations and also solves the universally frustrating dilemma of plugging a USB cable in correctly because it’s reversible! Read more...

  • BOB-15100
£4.80
Only 8 left!

WAV Trigger

The WAV Trigger is a unique high-fidelity polyphonic audio player with surprising capabilities. Supporting up to 2048 uncompressed 16-bit, 44.1kHz wav files – the same quality as an audio CD – the WAV Trigger can play and mix up to 14 stereo tracks simultaneously and independently, with very low latency. Read more...

  • WIG-13660
£49.50
Only 1 left!

SparkFun gator:starter ProtoSnap

The SparkFun gator:starter ProtoSnap is one of a series of gator-clippable accessories called gator:boards that have been created to directly interface with the micro:bit or to other micro controllers! The gator:starter ProtoSnap provides you with a starting point to go beyond the capabilities of the micro:bit, with three different boards that can be kept as a whole or broken apart for individual use! Read more...

  • SEN-14891
£10
Only 4 left!

SparkFun gator:color ProtoSnap

The SparkFun gator:color ProtoSnap is one of a series of gator-clippable accessories called gator:boards created to directly interface with the micro:bit or to other micro controllers! The gator:color ProtoSnap is perfect if you want to add a low-profile, glowing component to your project. It is equipped with six LED boards that can be kept as a whole or broken apart for individual use! Read more...

  • COM-14890
£10
Only 5 left!

SparkFun gator:control ProtoSnap

The SparkFun gator:control ProtoSnap is one of a series of gator-clippable accessories called gator:boards that have been created to directly interface with the micro:bit or to other micro controllers! The gator:control ProtoSnap offers a handful of ways to interact with projects you create using only gator-clip cables. Each little board on this ProtoSnap can be kept as a whole while on the board or broken apart for individual use! Read more...

  • COM-14968
£10
Only 7 left!

Lilypad USB Plus

This is the LilyPad USB Plus, a sewable electronics microcontroller board controlled by an ATmega32U4 with the Arduino bootloader. It has a built in power supply JST (and recharge circuit) and an on/off switch with the only extra piece of hardware you need to program the LilyPad USB Plus being a micro-USB cable. Read more...

  • DEV-14631
£27
Only 7 left!

LilyPad Light Sensor

The LilyPad Light Sensor is a sewable breakout board with an ALS-PT19 light sensor built in and ready to use right away. Read more...

  • DEV-14629
£3
Only 1 left!

SparkFun gator:bit

The SparkFun gator:bit is an all-in-one “carrier” board for your micro:bit that provides you with a fully functional development and prototyping platform. Almost every pin on the micro:bit is broken out to pads that alligator (or crocodile, if you prefer) clips so you can get the most out of it! Read more...

  • DEV-14484
£21
Only 5 left!