{"product_id":"rp2350-stamp-xl","title":"RP2350 Stamp XL","description":"\u003cp\u003eA hand-solderable RP2350B module with 16MB FLASH, LiPo charging, reset\/boot buttons, and all GPIO broken out.\u003c\/p\u003e\n\u003cp\u003eThe RP2350 Stamp XL is a hand-solderable SMD\/TH module that integrates the Raspberry Pi RP2350B MCU with 16MB of FLASH, an LDO, LiPo charge management (including a charge LED), a reset button, and a bootsel button. It breaks out all the 48 GPIOs as well as USB, SWD, BOOTSEL, RST, and the voltage pins. The Stamp also has a footprint for a second QSPI FLASH\/PSRAM, as well as footprints for SWD and UART JST connectors, compatible with the \u003ca href=\"\/en-eu\/products\/raspberry-pi-debug-probe\" rel=\"noopener\" target=\"_blank\"\u003eRaspberry Pi Debug Probe\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003eThe Stamp XL was created to allow you to use the Raspberry Pi RP2350B in your designs without having to solder small-pitch QFN chips or worry about lots of external circuitry.\u003c\/p\u003e\n\u003cp\u003eAll you need to get you started is a 5V supply or a LiPo battery. The Stamp will take care of the charging and switching the power sources.\u003c\/p\u003e\n\u003cp\u003eThe castellated edges with\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e2mm pitch\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003ecan be hand-soldered directly to a Carrier board, used with pin headers for more flexibility, or connected without soldering using \u003ca href=\"\/en-eu\/products\/flexypin-pack-of-100\" rel=\"noopener\" target=\"_blank\"\u003eFlexyPins\u003c\/a\u003e, which are spring connectors designed for modules with castellated edges.\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eYou can find footprints for many PCB programs including KiCad, Eagle CAD, and EasyEDA\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e\u003ca href=\"https:\/\/github.com\/solderparty\/rp2xxx_stamp_footprints\/\"\u003ehere\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cp\u003eAt only\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e1 by 1¾ inch\u003c\/strong\u003e, the Stamp XL packs a lot of features:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e16MB of FLASH\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e500mA 3.3V LDO\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eAll 48 GPIOs broken out\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eA footprint for a second QSPI FLASH\/PSRAM\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003eFootprints for SWD and UART JST connectors, pin-compatible with the Raspberry Pi Debug Probe\u003c\/li\u003e\n\u003cli\u003eLiPo supply and charging circuit (with charging LED)\u003c\/li\u003e\n\u003cli\u003eUSB broken out\u003c\/li\u003e\n\u003cli\u003eSWD broken out\u003c\/li\u003e\n\u003cli\u003eReset Button\u003c\/li\u003e\n\u003cli\u003eBootsel Button\u003c\/li\u003e\n\u003cli\u003e12MHz crystal\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eand of course, everything that comes with the Raspberry Pi RP2350 itself:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eDual core ARM Cortex-M33 or Hazard3 @ 150MHz\u003c\/li\u003e\n\u003cli\u003e520kB SRAM\u003c\/li\u003e\n\u003cli\u003e2 UARTs\u003c\/li\u003e\n\u003cli\u003e2 SPIs\u003c\/li\u003e\n\u003cli\u003e2 I2Cs\u003c\/li\u003e\n\u003cli\u003e24 PWM channels\u003c\/li\u003e\n\u003cli\u003e12 PIO state machines\u003c\/li\u003e\n\u003cli\u003e1 HSTX peripheral\u003c\/li\u003e\n\u003cli\u003eUSB with Host and Device support\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe RP2350 comes with a pre-programmed ROM UF2 Bootloader, by pulling the BOOTSEL pin low and resetting, or by double-pressing the RESET button (if the FW supports it), you can upload new firmware using the USB disk drive.\u003c\/p\u003e\n\u003ch2\u003eLinks to code and documentation\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/docs.solder.party\/rp2350-stamp-xl\" rel=\"noopener\" target=\"_blank\"\u003eDocumentation (docs.solder.party)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/github.com\/adafruit\/circuitpython\" rel=\"noopener\" target=\"_blank\"\u003eCode (github.com)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/github.com\/solderparty\/rp2350_stamp_xl_hw\" rel=\"noopener\" target=\"_blank\"\u003eDesign Files (github.com)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/github.com\/solderparty\/rp2350_stamp_xl_hw\/blob\/main\/schematics.pdf\" rel=\"noopener\" target=\"_blank\"\u003eSchematics (github.com)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/certification.oshwa.org\/se000026.html\" rel=\"noopener\" target=\"_blank\"\u003eCertified Open Source Hardware - OSHW SE000026\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cimg\u003e\u003cimg\u003e\u003cimg\u003e\u003cimg\u003e\u003cimg\u003e\u003cimg\u003e\u003c\/p\u003e","brand":"Solder Party","offers":[{"title":"Default Title","offer_id":53521688002939,"sku":"SP046","price":11.95,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/files\/IMG_0011_1.jpg?v=1731688568","url":"https:\/\/shop.pimoroni.com\/en-eu\/products\/rp2350-stamp-xl","provider":"Pimoroni Ltd","version":"1.0","type":"link"}