{"product_id":"rp2040-stamp","title":"RP2040 Stamp","description":"\u003cp\u003eA hand-solderable SMD\/TH module w\/ RP2040 MCU+8MB FLASH, LDO, LiPo charger, reset btn, and Neopixel. Breaks out all GPIO+USB+SWD+BOOTSEL+RST\u003c\/p\u003e\n\u003cp\u003eThe RP2040 Stamp is a hand-solderable SMD\/TH module that integrates the \u003cstrong\u003eRaspberry Pi RP2040\u003c\/strong\u003e MCU with 8MB of FLASH, an LDO, LiPo charge management (including a charge LED), a reset button, and a Neopixel.\u003c\/p\u003e\n\u003cp\u003eIt breaks out all the GPIOs as well as USB, SWD, BOOTSEL, RST, and the voltage pins.\u003c\/p\u003e\n\u003cp\u003eIf you want to get into the technical stuff, see the \u003ca href=\"https:\/\/rp2040-stamp.solder.party\/rp2040_stamp_datasheet.pdf\" target=\"_blank\"\u003eRP2040 Stamp Datasheet\u003c\/a\u003e to learn even more!\u003c\/p\u003e\n\u003cp\u003eThe Stamp was created to allow you to use the Raspberry Pi RP2040 in your designs without having to solder small-pitch QFN chips or worry about lots of external circuitry.\u003c\/p\u003e\n\u003cp\u003eAll you need to get you started is a 5V supply or a LiPo battery. The Stamp will take care of the charging and switching the power sources.\u003c\/p\u003e\n\u003cp\u003eThe castellated edges with \u003cstrong\u003e2mm pitch\u003c\/strong\u003e can be hand-soldered directly to a carrier board or by using pin headers. \u003ca href=\"https:\/\/github.com\/solderparty\/rp2040_stamp_footprints\/\" target=\"_blank\"\u003eYou can find footprints for many PCB programs including KiCad (5 and 6), Eagle CAD, and EasyEDA here\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003eAt only \u003cstrong\u003e1 by 1 inch\u003c\/strong\u003e (25mm x 25mm), the Stamp packs a lot of features:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e8MB of FLASH\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e500mA 3.3V LDO\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eAll 30 GPIOs broken out\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eA Neopixel\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003eLiPo supply and charging circuit (with charging LED)\u003c\/li\u003e\n\u003cli\u003eUSB broken out\u003c\/li\u003e\n\u003cli\u003eSWD broken out\u003c\/li\u003e\n\u003cli\u003eReset Button\u003c\/li\u003e\n\u003cli\u003e12MHz crystal\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eand of course, everything that comes with the Raspberry Pi RP2040 itself:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eDual core ARM Cortex-M0+ @ 133MHz\u003c\/li\u003e\n\u003cli\u003e264kB SRAM\u003c\/li\u003e\n\u003cli\u003e2 UARTs\u003c\/li\u003e\n\u003cli\u003e2 SPIs\u003c\/li\u003e\n\u003cli\u003e2 I2Cs\u003c\/li\u003e\n\u003cli\u003e16 PWM channels\u003c\/li\u003e\n\u003cli\u003eUSB with Host and Device support\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe RP2040 MCU comes with a pre-programmed ROM UF2 Bootloader, by pulling the BOOTSEL pin low and resetting, or by double-pressing the RESET button (if the FW supports it), you can upload new firmware using the USB disk drive.\u003c\/p\u003e\n\u003cp\u003eThe RP2040 Stamp board comes pre-flashed with CircuitPython 7.1.0-beta.1, if you want to use it with CircuitPython, it's recommended that you \u003ca href=\"https:\/\/circuitpython.org\/board\/solderparty_rp2040_stamp\/\" target=\"_blank\"\u003echeck for the latest version\u003c\/a\u003e and if there is one, update it according to the method mentioned above.\u003c\/p\u003e\n\u003cp\u003eIn addition to the Stamp, we also offer a reference design - \u003ca href=\"\/en-eu\/products\/rp2040-stamp-carrier\" target=\"_blank\"\u003ethe RP2040 Stamp Carrier.\u003c\/a\u003e\u003c\/p\u003e\n\u003ch2\u003eIncludes\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eA RP2040 Stamp module\u003c\/li\u003e\n\u003cli\u003eA pinout and functionality reference sheet\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSpecs and Docs\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/github.com\/adafruit\/circuitpython\" target=\"_blank\"\u003eSource Code\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/rp2040-stamp.solder.party\/\" target=\"_blank\"\u003eDocumentation\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/github.com\/solderparty\/rp2040_stamp_carrier_hw\" target=\"_blank\"\u003eDesign Files\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Solder Party","offers":[{"title":"Default Title","offer_id":39567567028307,"sku":"SP011","price":11.95,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/products\/KAB_9493_1abdbb3a-3803-451d-9270-88aec5bdc7c1.jpg?v=1640106457","url":"https:\/\/shop.pimoroni.com\/en-eu\/products\/rp2040-stamp","provider":"Pimoroni Ltd","version":"1.0","type":"link"}