{"product_id":"drv8256p-single-brushed-dc-motor-driver-carrier","title":"DRV8256P Single Brushed DC Motor Driver Carrier","description":"\u003cp\u003eThis compact breakout board for TI’s DRV8256P motor driver offers a wide operating voltage range of 4.5 V to 48 V and can deliver a continuous 1.9 A (6.4 A peak for \u0026lt;1 second) to a single brushed DC motor.\u003c\/p\u003e\n\u003cp\u003eIt features a two-pin IN\/IN interface for direct control of the motor outputs and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature\u003c\/p\u003e\n\u003cp\u003eTexas Instruments’ DRV8256P is a tiny H-bridge motor driver IC that can be used for bidirectional control of a single brushed DC motor at 4.5 V to 48 V. It can supply up to about 1.9 A continuously and can tolerate peak currents up to 6.4 A for a few seconds, making it a good choice for small motors that run on a wide range of voltages. Since this board is a carrier for the DRV8256P, we recommend careful reading of the \u003ca href=\"https:\/\/www.ti.com\/lit\/ds\/symlink\/drv8256.pdf\" target=\"_blank\"\u003eDRV8256 datasheet\u003c\/a\u003e. The board ships populated with all of its SMD components, including the DRV8256P.\u003c\/p\u003e\n\u003cp\u003eThis DRV8256\u003cstrong\u003eP\u003c\/strong\u003e has an IN\/IN interface that requires two PWM signals for full bidirectional control, but it offers drive\/brake operation (which usually provides a more linear relationship between PWM duty cycle and motor speed). The very similar DRV8256\u003cstrong\u003eE\u003c\/strong\u003e uses a phase\/enable interface instead, allowing bidirectional control with only one PWM signal, but it is limited to drive\/coast operation. \u003ca href=\"\/en-eu\/products\/drv8256e-single-brushed-dc-motor-driver-carrier\" target=\"_blank\"\u003eWe sell another version of this carrier board with the DRV8256E;\u003c\/a\u003e the two versions can be distinguished by the markings on the driver chip.\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eDrives a single brushed DC motor\u003c\/li\u003e\n\u003cli\u003eMotor supply voltage: 4.5 V to 48 V\u003c\/li\u003e\n\u003cli\u003eSupports 1.8 V to 5 V logic voltage (5.5 V max)\u003c\/li\u003e\n\u003cli\u003eOutput current: 1.9 A continuous (6.4 A peak)\u003c\/li\u003e\n\u003cli\u003eUnder-voltage lockout and protection against over-current and over-temperature\u003c\/li\u003e\n\u003cli\u003eCarrier board adds reverse-voltage protection up to 40 V\u003c\/li\u003e\n\u003cli\u003eCompact size (0.6″×0.6″)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eUsing the motor driver\u003c\/h2\u003e\n\u003cp\u003eIn a typical application, power connections are made on one side of the board and control connections are made on the other. Aside from motor and power connections (including a logic voltage connection to SLEEP), the only required control pins are IN1 and IN2.\u003c\/p\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth colspan=\"5\"\u003eDRV8256P Truth Table\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eIN1\u003c\/th\u003e\n\u003cth\u003eIN2\u003c\/th\u003e\n\u003cth\u003eOUT1\u003c\/th\u003e\n\u003cth\u003eOUT2\u003c\/th\u003e\n\u003cth\u003eoperating mode\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e0\u003c\/td\u003e\n\u003ctd\u003e0\u003c\/td\u003e\n\u003ctd\u003eL\u003c\/td\u003e\n\u003ctd\u003eL\u003c\/td\u003e\n\u003ctd\u003ebrake low (outputs shorted to ground)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePWM\u003c\/td\u003e\n\u003ctd\u003e0\u003c\/td\u003e\n\u003ctd\u003ePWM (H\/L)\u003c\/td\u003e\n\u003ctd\u003eL\u003c\/td\u003e\n\u003ctd\u003eforward\/brake at speed PWM %\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e0\u003c\/td\u003e\n\u003ctd\u003ePWM\u003c\/td\u003e\n\u003ctd\u003eL\u003c\/td\u003e\n\u003ctd\u003ePWM (H\/L)\u003c\/td\u003e\n\u003ctd\u003ereverse\/brake at speed PWM %\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e1\u003c\/td\u003e\n\u003ctd\u003e1\u003c\/td\u003e\n\u003ctd\u003eH\u003c\/td\u003e\n\u003ctd\u003eH\u003c\/td\u003e\n\u003ctd\u003ebrake high (outputs shorted to VM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch2\u003ePinout\u003c\/h2\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003ePIN\u003c\/th\u003e\n\u003cth\u003eDefault State\u003c\/th\u003e\n\u003cth\u003eDescription\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eVIN\u003c\/td\u003e\n\u003ctd\u003e\u003c\/td\u003e\n\u003ctd\u003e4.5 V to 48 V board power supply input (reverse-protected up to 40 V).\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eGND\u003c\/td\u003e\n\u003ctd\u003e\u003c\/td\u003e\n\u003ctd\u003eGround connection points for the motor and logic supplies. The control source and the motor driver must share a common ground.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eVM\u003c\/td\u003e\n\u003ctd\u003e\u003c\/td\u003e\n\u003ctd\u003eThis pin gives access to the motor power supply after the reverse-voltage protection MOSFET (see the board schematic below). It can be used to supply reverse-protected power to other components in the system.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOUT1\u003c\/td\u003e\n\u003ctd\u003e\u003c\/td\u003e\n\u003ctd\u003eMotor output 1.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOUT2\u003c\/td\u003e\n\u003ctd\u003e\u003c\/td\u003e\n\u003ctd\u003eMotor output 2.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIN1\u003c\/td\u003e\n\u003ctd\u003eLOW\u003c\/td\u003e\n\u003ctd\u003eControl input for OUT1. PWM can be applied to this pin.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIN2\u003c\/td\u003e\n\u003ctd\u003eLOW\u003c\/td\u003e\n\u003ctd\u003eControl input for OUT2. PWM can be applied to this pin.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFAULT\u003c\/td\u003e\n\u003ctd\u003eFLOATING\u003c\/td\u003e\n\u003ctd\u003eOpen-drain, active-low fault output. This pin goes low during an over-current, over-temperature, or under-voltage condition. You must use an external pull-up resistor to give this pin a default high value if you want to use it.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSLEEP\u003c\/td\u003e\n\u003ctd\u003eLOW\u003c\/td\u003e\n\u003ctd\u003eSleep input that puts the DRV8256P into a low-power sleep mode when low. This pin can also be toggled to clear a latched over-current or over-temperature fault.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eVREF\u003c\/td\u003e\n\u003ctd\u003e\u003c\/td\u003e\n\u003ctd\u003eCurrent limiting threshold reference voltage (see below).\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch2\u003eCurrent limiting\u003c\/h2\u003e\n\u003cp\u003eThe DRV8256 can actively limit the current through the motors by using a fixed off-time PWM current regulation (current chopping). The current limit is determined by the voltage on the VREF pin, which this carrier board pulls up to 5 V (DVDD) through a 47 kΩ resistor, setting the current limit to 6.4 A (the maximum possible). You can lower the current limit by connecting an additional resistor between VREF and GND or by connecting an external reference voltage directly to VREF. Refer to the DRV8256 datasheet for more information about the driver’s current regulation.\u003c\/p\u003e\n\u003ch2\u003eReal-world power dissipation considerations\u003c\/h2\u003e\n\u003cp\u003eThe DRV8256 datasheet rates this driver for a peak current of 6.4 A, and that is the highest current limiting threshold that can be configured for it. However, the chip by itself will overheat at lower currents. In Pololu's tests, they found that the chip was able to deliver 5 A for only a few seconds or 6.4 A for less than a second before the chip’s thermal protection kicked in and disabled the motor outputs; a continuous current of about 1.9 A was sustainable for many minutes without triggering a thermal shutdown.\u003c\/p\u003e\n\u003cp\u003eThe actual current you can deliver will depend on how well you can keep the motor driver cool. The carrier’s printed circuit board is designed to help with this by drawing heat out of the motor driver chip. PWMing the motor will introduce additional heating proportional to the frequency.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThis product can get \u003cspan style=\"color: #ff2a00;\"\u003ehot\u003c\/span\u003e enough to burn you long before the chip overheats. Take care when handling this product and other components connected to it.\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch2\u003eIncluded hardware\u003c\/h2\u003e\n\u003cp\u003eBreakaway 0.1″ male headers are included with the DRV8256P motor driver carrier, which can be soldered in to use the driver with perfboards, breadboards, or 0.1″ female connectors. (The headers might ship as a single larger strip that can be broken into smaller pieces.) When used with these header pins, the board can be oriented with the parts visible, or with the silkscreen visible, by soldering the headers in from the opposite side. You can also solder your motor leads and other connections directly to the board.\u003c\/p\u003e\n\u003ch2\u003eSchematic\u003c\/h2\u003e\n\u003cp\u003eThe schematic is available as a downloadable pdf: \u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/files\/drv8256x-single-brushed-dc-motor-driver-carrier-schematic.pdf?v=1638805512\" target=\"_blank\" data-mce-href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/files\/drv8256x-single-brushed-dc-motor-driver-carrier-schematic.pdf?v=1638805512\"\u003eDRV8256E\/P Single Brushed DC Motor Driver Carrier schematic\u003c\/a\u003e\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eMotor driver\u003c\/td\u003e\n\u003ctd\u003eDRV8256P\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMotor channels\u003c\/td\u003e\n\u003ctd\u003e1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMinimum operating voltage\u003c\/td\u003e\n\u003ctd\u003e4.5 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaximum operating voltage\u003c\/td\u003e\n\u003ctd\u003e48 V\u003csup\u003e1\u003c\/sup\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eContinuous output current per channel\u003c\/td\u003e\n\u003ctd\u003e1.9 A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePeak output current per channel\u003c\/td\u003e\n\u003ctd\u003e6.4 A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaximum PWM frequency\u003c\/td\u003e\n\u003ctd\u003e100 kHz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMinimum logic voltage\u003c\/td\u003e\n\u003ctd\u003e1.8 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaximum logic voltage\u003c\/td\u003e\n\u003ctd\u003e5.5 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eReverse voltage protection?\u003c\/td\u003e\n\u003ctd\u003eY\u003csup\u003e2\u003c\/sup\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHeader pins soldered?\u003c\/td\u003e\n\u003ctd\u003eN\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cem\u003e\u003csup\u003e1\u003c\/sup\u003e Not recommended for use with 48V batteries.\u003c\/em\u003e\u003cbr\u003e\u003cem\u003e\u003csup\u003e2\u003c\/sup\u003e Note: Reverse voltage protection only works up to 40 V.\u003c\/em\u003e\u003c\/p\u003e\n\u003ch2\u003eResources\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/www.pololu.com\/file\/0J1838\/drv8256x-single-brushed-dc-motor-driver-carrier-schematic.pdf\" target=\"_blank\"\u003eSchematic diagram of the DRV8256x Single Brushed DC Motor Driver Carrier\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/www.pololu.com\/file\/0J1840\/drv8256x-single-brushed-dc-motor-driver-carrier-dimensions.pdf\" target=\"_blank\"\u003eDimension diagram of the DRV8256x Single Brushed DC Motor Driver Carrier\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/www.pololu.com\/file\/0J1841\/drv8256x-single-brushed-dc-motor-driver-carrier.step\" target=\"_blank\"\u003e3D model of the DRV8256x Single Brushed DC Motor Driver Carrier\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/www.pololu.com\/file\/0J1839\/md42a-drill.dxf\" target=\"_blank\"\u003eDrill guide for the DRV8256x Single Brushed DC Motor Driver Carrier\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Pololu","offers":[{"title":"Default Title","offer_id":39576556830803,"sku":"POL-4039","price":14.95,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/products\/0J11307.1200.jpg?v=1638809500","url":"https:\/\/shop.pimoroni.com\/en-eu\/products\/drv8256p-single-brushed-dc-motor-driver-carrier","provider":"Pimoroni Ltd","version":"1.0","type":"link"}