{"product_id":"adafruit-metro-m4-express-airlift-wifi-lite","title":"Adafruit Metro M4 Express AirLift (WiFi) - Lite","description":"\u003cp\u003eGive your next project a lift with \u003cem\u003eAirLift\u003c\/em\u003e - Adafruit's witty name for the ESP32 co-processor that graces this Metro M4.\u003c\/p\u003e\n\u003cp\u003eYou already know about the \u003cstrong\u003eAdafruit Metro M4\u003c\/strong\u003e featuring the \u003cstrong\u003eMicrochip ATSAMD51\u003c\/strong\u003e, with its 120MHz Cortex M4 with floating point support. With a train-load of FLASH and RAM, your code will be fast and roomy. And what better way to improve it than to add wireless? Now cooked in directly on board, you get a certified WiFi module that can handle all your TLS and socket needs, it even has root certificates pre-loaded.\u003c\/p\u003e\n\u003cp\u003eThis Metro is the same size as the others, and is compatible with all Adafruit shields. It's got analog pins where you expect, and SPI\/UART\/I2C hardware support in the same spot as the Metro 328 and M0. But! It's powered with an ATSAMD51J19:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCortex M4 core running at \u003cstrong\u003e120 MHz\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/developer.arm.com\/technologies\/dsp\/dsp-for-cortex-m\" target=\"_blank\" rel=\"noopener noreferrer\"\u003eFloating point support with Cortex M4 DSP instructions\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e512 KB\u003c\/strong\u003e flash, \u003cstrong\u003e192 KB\u003c\/strong\u003e RAM\u003c\/li\u003e\n\u003cli\u003e32-bit, 3.3V logic and power\u003c\/li\u003e\n\u003cli\u003eDual 1 MSPS DAC (A0 and A1)\u003c\/li\u003e\n\u003cli\u003eDual 1 MSPS ADC (8 analog pins)\u003c\/li\u003e\n\u003cli\u003e6 x hardware SERCOM (I2C, SPI or UART)\u003c\/li\u003e\n\u003cli\u003e22 x PWM outputs\u003c\/li\u003e\n\u003cli\u003eStereo I2S input\/output with MCK pin\u003c\/li\u003e\n\u003cli\u003e10-bit Parallel capture controller (for camera\/video in)\u003c\/li\u003e\n\u003cli\u003eBuilt in crypto engines with AES (256 bit), true RNG, Pubkey controller\u003c\/li\u003e\n\u003cli\u003e64 QFN\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003ePretty good start right? So Adafruit put this chip on a PCB with all these nice extras:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower the METRO M4\u003c\/strong\u003e with 7-9V polarity protected DC or the micro USB connector to any 5V USB source. The 2.1mm DC jack has an on\/off switch next to it so you can turn off your setup easily. The METRO will automagically switch between USB and DC.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMETRO has 25 GPIO pins\u003c\/strong\u003e, 8 of which are analog in, and two of which is a true analog out. There's a hardware SPI port, hardware I2C port and hardware UART. Logic level is 3.3V\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNative USB\u003c\/strong\u003e, there's no need for a hardware USB to Serial converter as the Metro M4 has built in USB support. When used to act like a serial device, the USB interface can be used by any computer to listen\/send data to the METRO, and can also be used to launch and update code via the bootloader. It can also act like an HID keyboard or mouse.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAirLift WiFi Co-processor\u003c\/strong\u003e, with TLS\/SSL support, plenty of RAM for sockets, communication is over SPI and has Arduino and CircuitPython libraries ready to go for fast wireless integration.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFour indicator LEDs and one NeoPixel\u003c\/strong\u003e, on the back edge of the PCB, for easy debugging. One green power LED, two RX\/TX LEDs for data being sent over USB, and a red LED connected. Next to the reset button there is an RGB NeoPixel that can be used for any purpose.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e2 MB QSPI Flash \u003c\/strong\u003estorage chip is included on board. You can use the SPI Flash storage like a very tiny hard drive. When used in CircuitPython, the 2 MB flash acts as storage for all your scripts, libraries and files. When used in Arduino, you can read\/write files to it, like a little datalogger or SD card, and then with the helper program, access the files over USB.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEasy reprogramming\u003c\/strong\u003e, comes pre-loaded with the \u003ca href=\"https:\/\/learn.adafruit.com\/adafruit-metro-m0-express-designed-for-circuitpython\/uf2-bootloader\" target=\"_blank\" rel=\"noopener noreferrer\"\u003eUF2 bootloader\u003c\/a\u003e, which looks like a USB storage key. Simply drag firmware on to program, no special tools or drivers needed! It can be used to load up CircuitPython or Arduino IDE (it is bossa v1.8 compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eAdafruit have a working Arduino board support package, with lots of stuff working, but their primary target for this board is CircuitPython - with 120 MHz, and 192KB of RAM CircuitPython runs really well on this chip! CircuitPython's built in support for JSON parsing plus their \u003cem\u003erequests \u003c\/em\u003ecompatible library makes it incredibly easy to build secure IoT projects in just a few minutes.\u003c\/p\u003e\n\u003cp\u003eSo what are you waiting for? Pick up a Metro M4 AirLift today and be amazed at how easy and fast it is to get started with IoT projects using CircuitPython!\u003c\/p\u003e\n\u003ch2\u003eTECHNICAL DETAILS\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003ePlease note this board has 0.1\" instead of 0.125\" standard mounting holes, which may affect mounting hardware choices if you're using an Arduino case.\u003c\/li\u003e\n\u003cli\u003eProduct Dimensions: 72.0mm x 54.0mm x 15.0mm \/ 2.8\" x 2.1\" x 0.6\"\u003c\/li\u003e\n\u003cli\u003eProduct Weight: 21.8g \/ 0.8oz\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eLEARN\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/learn.adafruit.com\/adafruit-io-basics-airlift\"\u003eAdafruit IO Basics: AirLift\u003c\/a\u003e - Get your project online fast with AirLift \u0026amp; Adafruit IO!\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Adafruit","offers":[{"title":"Default Title","offer_id":27866314473555,"sku":"ADA4000","price":34.95,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/products\/4000-03.jpg?v=1556698682","url":"https:\/\/shop.pimoroni.com\/en-eu\/products\/adafruit-metro-m4-express-airlift-wifi-lite","provider":"Pimoroni Ltd","version":"1.0","type":"link"}