{"product_id":"adafruit-feather-m0-adalogger","title":"Adafruit Feather M0 Adalogger","description":"\u003cp\u003eThis is the \u003cstrong\u003eAdafruit Feather M0 Adalogger\u003c\/strong\u003e - Adafruits take on an 'all-in-one' Cortex M0 datalogger (or data-reader) with built in USB and battery charging.\u003c\/p\u003e\n\u003cp\u003eIts an Adafruit Feather M0 with a microSD holder ready to rock! \u003ca href=\"https:\/\/shop.pimoroni.com\/search?type=product\u0026amp;q=feather\" target=\"_blank\"\u003eWe have other boards in the Feather family, check'em out here\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003eAt the Feather M0's heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program \u0026amp; debug capability built in with no need for an FTDI-like chip.\u003c\/p\u003e\n\u003cp\u003eTo make it easy to use for portable projects, Adafruit added a connector for any of their 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. We also tied the battery thru a divider to an analog pin, so you can measure and monitor the battery voltage to detect when you need a recharge.\u003c\/p\u003e\n\u003cp\u003eHere's some handy specs! Like all Feather M0's you get:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMeasures 2.0\" x 0.9\" x 0.28\" (51mm x 23mm x 8mm) without headers soldered in\u003c\/li\u003e\n\u003cli\u003eLight as a (large?) feather - 5.3 grams\u003c\/li\u003e\n\u003cli\u003eATSAMD21G18 @ 48MHz with 3.3V logic\/power\u003c\/li\u003e\n\u003cli\u003e256KB of FLASH + 32KB of RAM\u003c\/li\u003e\n\u003cli\u003e3.3V regulator with 500mA peak current output\u003c\/li\u003e\n\u003cli\u003eUSB native support, comes with USB bootloader and serial port debugging\u003c\/li\u003e\n\u003cli\u003eYou also get tons of pins - 20 GPIO pins\u003c\/li\u003e\n\u003cli\u003eHardware Serial, hardware I2C, hardware SPI support\u003c\/li\u003e\n\u003cli\u003e8 x PWM pins\u003c\/li\u003e\n\u003cli\u003e10 x analog inputs\u003c\/li\u003e\n\u003cli\u003eBuilt in 100mA lipoly charger with charging status indicator LED\u003c\/li\u003e\n\u003cli\u003ePin #13 red LED for general purpose blinking\u003c\/li\u003e\n\u003cli\u003ePower\/enable pin\u003c\/li\u003e\n\u003cli\u003e4 mounting holes\u003c\/li\u003e\n\u003cli\u003eReset button\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe \u003cstrong\u003eFeather M0 Adalogger\u003c\/strong\u003e uses the extra space left over to add MicroSD + a green LED:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePin #8 green LED for your blinking pleasure\u003c\/li\u003e\n\u003cli\u003eMicroSD card holder for adding as much storage as you could possibly want, for reading or writing.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eComes fully assembled and tested, with a USB bootloader that lets you quickly use it with the Arduino IDE. Adafruit also toss in some header so you can solder it in and plug into a solderless breadboard. \u003cstrong\u003eLipoly battery, MicroSD card and USB cable not included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/learn.adafruit.com\/adafruit-feather-m0-adalogger\/\" target=\"_blank\"\u003eCheck out the tutorial for all sorts of details, including schematics, files, IDE instructions, and more!\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTECHNICAL DETAILS\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e22.8mm x 51.6mm x 8mm \/ 0.9\" x 2.0\" x 0.28\"\u003c\/li\u003e\n\u003cli\u003eWeight: 5.3g\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Adafruit","offers":[{"title":"Default Title","offer_id":11892212935,"sku":"ADA2796","price":19.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/products\/2796.jpg?v=1450370888","url":"https:\/\/shop.pimoroni.com\/en-eu\/products\/adafruit-feather-m0-adalogger","provider":"Pimoroni Ltd","version":"1.0","type":"link"}