{"product_id":"5v-step-up-step-down-voltage-regulator-s13v30f5","title":"5V Step-Up\/Step-Down Voltage Regulator","description":"\u003cp\u003eThis powerful synchronous switching step-up\/step-down regulator efficiently produces 5 V from input voltages between 2.8 V and 22 V.\u003c\/p\u003e\n\u003cp\u003eIts ability to convert both higher and lower input voltages makes it useful for applications where the power supply voltage can vary greatly, as with batteries that start above but discharge below 5 V.\u003c\/p\u003e\n\u003cp\u003eThe S13VxF5 family of efficient switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters) use a buck-boost topology to convert both higher and lower input voltages to a regulated 5 V output. They take input voltages from 2.8 V to 22 V and increase or decrease them as necessary, offering a typical efficiency of over 85% and typical continuous output currents between 1 A and 3 A . The flexibility in input voltage offered by this family of regulators is especially well-suited for battery-powered applications in which the battery voltage begins above 5 V and drops below as the battery discharges. Without the typical restriction on the battery voltage staying above the required voltage throughout its life, new battery packs and form factors can be considered.\u003c\/p\u003e\n\u003cp\u003eThe different members of this family offer different continuous output currents:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eS13V10F5: 1 A continuous output current\u003c\/li\u003e\n\u003cli\u003eS13V15F5: 1.5 A continuous output current\u003c\/li\u003e\n\u003cli\u003eS13V20F5: 2 A continuous output current\u003c\/li\u003e\n\u003cli\u003eS13V30F5: 3 A continuous output current\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe regulators have under-voltage lockout, output over-voltage protection, and over-current protection. A thermal shutdown feature also helps prevent damage from overheating and a soft-start feature limits the inrush current and gradually ramps the output voltage on startup. The larger 3 A S13V30F5 has reverse-voltage protection up to 20 V, but the S13V10F5, S13V15F5, and S13V20F5 do not.\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eInput voltage: 2.8 V to 22 V\u003c\/li\u003e\n\u003cli\u003eOutput voltage: 5 V with 3% accuracy\u003c\/li\u003e\n\u003cli\u003eTypical efficiency of 85% to 95%, depending on input voltage and load (see the efficiency graph below)\u003c\/li\u003e\n\u003cli\u003e10 mA to 20 mA typical no-load quiescent current (see the quiescent current graph below)\u003c\/li\u003e\n\u003cli\u003eInput under-voltage lockout and output over-voltage protection\u003c\/li\u003e\n\u003cli\u003eSoft-start feature limits inrush current and gradually ramps output voltage\u003c\/li\u003e\n\u003cli\u003eIntegrated reverse-voltage protection up to 20 V (S13V30F5 only), over-current protection, and over-temperature shutoff\u003c\/li\u003e\n\u003cli\u003eFixed switching frequency of ~500 kHz\u003c\/li\u003e\n\u003cli\u003eCompact size:\n\u003cul\u003e\n\u003cli\u003eS13V30F5 - \u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/files\/5v-step-up-step-down-voltage-regulator-s13v30f5-dimensions.pdf?v=1649343250\" target=\"_blank\"\u003e0.9″ × 0.9″ × 0.38″ (22.9 mm × 22.9 mm × 9.7 mm)\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eS13V10F5, S13V15F5, \u0026amp; S13V20F5 - \u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/files\/5v-step-up-step-down-regulator-s13vxf5-dimensions.pdf?v=1649343181\" target=\"_blank\"\u003e0.35″ × 0.475″ × 0.17″ (8.9 mm × 12.1 mm × 4.2 mm)\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eConnections - S13V30F5\u003c\/h2\u003e\n\u003cp\u003eThe step-up\/step-down regulator has four connections: enable (EN), the input voltage (VIN), ground (GND), and the output voltage (VOUT). The input voltage, VIN, powers the regulator. Voltages between 2.8 V and 22 V can be applied to VIN. VOUT is the regulated output voltage.\u003c\/p\u003e\n\u003cp\u003eThe regulator, which is enabled by default, can be put into a low-power sleep state by bringing the EN pin low. The rising threshold for the EN pin is between 1 V and 1.2 V, and the falling threshold is at most 160 mV lower than that (i.e. the falling hysteresis is 160 mV max). This allows a precise low-VIN cutoff to be set, such as with the output of an external voltage divider powered by VIN, which can be useful for battery powered applications where draining the battery below a particular voltage threshold could permanently damage it. The quiescent current draw in sleep mode is dominated by the current in the 475 kΩ pull-up resistor from ENABLE to VIN and in the reverse-voltage protection circuit, which altogether will be between 2 µA and 10 µA per volt on VIN.\u003c\/p\u003e\n\u003cp\u003eThe regulator has two sets of through-holes: five smaller holes arranged with a 0.1″ spacing along the edge of the board (for compatibility with standard solderless breadboards and perfboards and connectors that use a 0.1″ grid) and four larger holes intended for 3.5 mm-pitch terminal blocks. VIN, GND, and VOUT are available at both the smaller holes and larger holes, but EN is only available on the smaller row of through-holes.\u003c\/p\u003e\n\u003cp\u003eThe regulator includes a 5×1 straight male header strip and two 2-pin, 3.5 mm-pitch terminal blocks, and it can be assembled with either the header or terminal blocks, \u003cstrong\u003enot both\u003c\/strong\u003e. The 0.1″ male header can be soldered into the smaller through-holes. Alternatively, the terminal blocks can be locked together and soldered into the larger holes to allow for convenient temporary connections of unterminated wires (see our short video on terminal block installation). You can also solder wires directly to the board for the most compact installation.\u003c\/p\u003e\n\u003cp\u003eIf the terminal blocks are used, a small wire (not included) can be soldered to the enable pin as shown below, so it will not interfere with the VIN terminal block connection.\u003c\/p\u003e\n\u003ch2\u003eConnections - S13V10F5, S13V15F5, \u0026amp; S13V20F5\u003c\/h2\u003e\n\u003cp\u003eThe step-up\/step-down regulator has just three connections: the input voltage (VIN), ground (GND), and the output voltage (VOUT). The input voltage, VIN, powers the regulator. Voltages between 2.8 V and 22 V can be applied to VIN. VOUT is the regulated output voltage.These through-holes are arranged with a 0.1″ spacing along the edge of the board for compatibility with standard solderless breadboards and perfboards and connectors that use a 0.1″ grid. A 3×1 straight male header strip and a 3×1 right-angle male header strip are included, and you can solder in the one that gives you your desired board orientation. Alternatively, you can solder wires directly to the board for the most compact installations.\u003c\/p\u003e\n\u003ch2\u003eTypical efficiency\u003c\/h2\u003e\n\u003cp\u003eThe efficiency of a voltage regulator, defined as (Power out)\/(Power in), is an important measure of its performance, especially when battery life or heat are concerns.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/files\/0J11267.600_480x480.png?v=1624270322\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/files\/0J11557.600_480x480.png?v=1649343547\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/files\/0J11556.600_480x480.png?v=1649343575\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/files\/0J11558.600_480x480.png?v=1649343597\" alt=\"\"\u003e\u003c\/p\u003e\n\u003ch2\u003eMaximum continuous output current\u003c\/h2\u003e\n\u003cp\u003eThe maximum achievable output current of the regulator varies with the input voltage but also depends on other factors, including the ambient temperature, air flow, and heat sinking. The graph below shows maximum output currents that the regulators in the S13VxF5 family can deliver continuously at room temperature in still air and without additional heat sinking.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/files\/0J11559.600_480x480.png?v=1649343650\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDuring normal operation, this product can get \u003cspan style=\"color: #ff2a00;\"\u003ehot\u003c\/span\u003e enough to burn you. Take care when handling this product or other components connected to it.\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch2\u003eQuiescent current\u003c\/h2\u003e\n\u003cp\u003eThe quiescent current is the current the regulator uses just to power itself, and the graph below shows this as a function of the input voltage. On S13V30F5 the module’s EN input can be driven low to put the board into a low-power state where it typically draws between 2 µA and 10 µA per volt on VIN.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/files\/0J11269.600_480x480.png?v=1624270426\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/files\/0J11560.600_480x480.png?v=1649343684\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003eTypically the quiescent current of the S13V30F5 is below 20 mA, but for input voltages between about 3 V and 3.3 V the quiescent current of some units can rise to near 100 mA. Keeping connections short and adding a capacitor of a few tens of microfarads greatly reduces this spike in quiescent current.\u003c\/p\u003e\n\u003ch2\u003eLC Voltage Spikes\u003c\/h2\u003e\n\u003cp\u003eWhen connecting voltage to electronic circuits, the initial rush of current can cause voltage spikes that are much higher than the input voltage. If these spikes exceed the regulator’s maximum voltage, the regulator can be destroyed. If you are connecting more than about 15 V, using power leads more than a few inches long, or using a power supply with high inductance, we recommend soldering a 33 μF or larger electrolytic capacitor close to the regulator between VIN and GND. The capacitor should be rated for at least 35 V.\u003c\/p\u003e\n\u003cp\u003eMore information about LC spikes can be found in our application note, \u003ca href=\"https:\/\/www.pololu.com\/docs\/0J16\" target=\"_blank\" rel=\"noopener noreferrer\"\u003eUnderstanding Destructive LC Voltage Spikes\u003c\/a\u003e.\u003c\/p\u003e","brand":"Pololu","offers":[{"title":"S13V30F5 - 3A","offer_id":39848138834003,"sku":"POL-4082","price":12.95,"currency_code":"EUR","in_stock":false},{"title":"S13V20F5 - 2A","offer_id":39848138932307,"sku":"POL-4085","price":12.95,"currency_code":"EUR","in_stock":false},{"title":"S13V15F5 - 1.5A","offer_id":39848138899539,"sku":"POL-4084","price":8.95,"currency_code":"EUR","in_stock":false},{"title":"S13V10F5 - 1A","offer_id":39848138866771,"sku":"POL-4083","price":6.95,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0174\/1800\/products\/0J11251.1200.jpg?v=1624271126","url":"https:\/\/shop.pimoroni.com\/en-eu\/products\/5v-step-up-step-down-voltage-regulator-s13v30f5","provider":"Pimoroni Ltd","version":"1.0","type":"link"}